No image available
Shopping Preview｜ Other Products ｜Chem-Wall Sealer
USD 61.09
Other Products / General Merchandise / Other Products
Chem-Wall Sealer
Available Sizes
1.5 Gallon Units
Advantages
100% solids
Excellent adhesion
High build formulation
Good chemical and abrasion resistance
Easy mix ratio and application methods
VOC compliant
Good UV resistance
Manufactured in a white color base, but able to be field pigmented in any ROCK-TRED Standard Color
Description
CHEM-WALL SEALER is 100% solids, high viscosity, 2-component, aliphatic epoxy. CHEM-WALL SEALER provides excellent durability, abrasion resistance and protection from a wide range of chemicals.
Uses
CHEM-WALL SEALER is used where a high-build protective polymer coating is desired on walls and ceilings. This coating is suitable for application as a neat finish coat over prepared and primed surfaces, or as a build/body coat between primer and high-performance finish coats such as CHEM-THANE WB. CHEM-WALL SEALER is easy to use, VOC compliant and meets all USDA/FDA guidelines for use in federally inspected facilities.
Typical Coverage
CHEM-WALL SEALER is normally installed at 135-200 square feet per gallon on vertical and overhead substrates.
Physical Properties
Volume mix ratio
2 to 1 (Resin to Hardener)
Viscosity (mixed)
19,000-25,000 CPS Typical
Solids Content (%)
100 % (ASTM D-2697)
Hardness (ASTM D-2240)
70-80 (Shore D)
VOC
Compliant with all US Regulations
Application Temps.
60° – 85° F
Gel Time
40-60 minutes @ 75° F
Dry to Touch (recoat with compatible products)
1-3 hours @ 75° F
Through Cure
6-8 hours @ 75° F
Open for light traffic/use
24 hours @ 75° F
Shelf Life
1 Year in unopened units
Limitations & For Best Results
Do not thin this product.
Do not apply when Humidity exceeds 70% indoors.
Do not allow to puddle during application.
Allow each coat to dry to ‘tack-free’ prior to re-coat
When re-coating, always apply the next coat within 24 hours of completing the previous coat.
CHEM-WALL SEALER is a WHITE COLOR BASE. Field pigmenting with ROCK-TRED standard colors will result in a lighter color than is shown on the ROCK-TRED STANDARD COLOR CHART.
Product Application
Apply using brush, roller and/or airless sprayer. ROCKTRED product test data is based on environmental temperatures of 75° F (24° C). Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.
Color and Textures
CHEM-WALL SEALER is manufactured as a white color base and can be field pigmented using one 1.5 Jar unit of ROCK-TRED UNIVERSAL colorant per 1.5-gal unit. Most ROCK-TRED products are available in a wide range of textures.
Chemical Resistance
Always refer to ROCK-TRED’s chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.
Product Storage
DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.
Surface Preparation
Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a diamond grinding machine to a minimum CSP-2 profile followed by application of an appropriate ROCK-TRED primer or base system is the best and recommended installation method for CHEM-WALL SEALER applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
Clean Up
Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.
Disposal
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
Important Notice
Always read and acquaint yourself with ROCK-TRED’s Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty
Brand:Rock TredSKU:RT430-COO-1.5Tags:Clear Epoxy, Rock Tred, Sealers
View productAvailable Sizes
1.5 Gallon Units
Advantages
100% solids
Excellent adhesion
High build formulation
Good chemical and abrasion resistance
Easy mix ratio and application methods
VOC compliant
Good UV resistance
Manufactured in a white color base, but able to be field pigmented in any ROCK-TRED Standard Color
Description
CHEM-WALL SEALER is 100% solids, high viscosity, 2-component, aliphatic epoxy. CHEM-WALL SEALER provides excellent durability, abrasion resistance and protection from a wide range of chemicals.
Uses
CHEM-WALL SEALER is used where a high-build protective polymer coating is desired on walls and ceilings. This coating is suitable for application as a neat finish coat over prepared and primed surfaces, or as a build/body coat between primer and high-performance finish coats such as CHEM-THANE WB. CHEM-WALL SEALER is easy to use, VOC compliant and meets all USDA/FDA guidelines for use in federally inspected facilities.
Typical Coverage
CHEM-WALL SEALER is normally installed at 135-200 square feet per gallon on vertical and overhead substrates.
Physical Properties
Volume mix ratio
2 to 1 (Resin to Hardener)
Viscosity (mixed)
19,000-25,000 CPS Typical
Solids Content (%)
100 % (ASTM D-2697)
Hardness (ASTM D-2240)
70-80 (Shore D)
VOC
Compliant with all US Regulations
Application Temps.
60° – 85° F
Gel Time
40-60 minutes @ 75° F
Dry to Touch (recoat with compatible products)
1-3 hours @ 75° F
Through Cure
6-8 hours @ 75° F
Open for light traffic/use
24 hours @ 75° F
Shelf Life
1 Year in unopened units
Limitations & For Best Results
Do not thin this product.
Do not apply when Humidity exceeds 70% indoors.
Do not allow to puddle during application.
Allow each coat to dry to ‘tack-free’ prior to re-coat
When re-coating, always apply the next coat within 24 hours of completing the previous coat.
CHEM-WALL SEALER is a WHITE COLOR BASE. Field pigmenting with ROCK-TRED standard colors will result in a lighter color than is shown on the ROCK-TRED STANDARD COLOR CHART.
Product Application
Apply using brush, roller and/or airless sprayer. ROCKTRED product test data is based on environmental temperatures of 75° F (24° C). Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.
Color and Textures
CHEM-WALL SEALER is manufactured as a white color base and can be field pigmented using one 1.5 Jar unit of ROCK-TRED UNIVERSAL colorant per 1.5-gal unit. Most ROCK-TRED products are available in a wide range of textures.
Chemical Resistance
Always refer to ROCK-TRED’s chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.
Product Storage
DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.
Surface Preparation
Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a diamond grinding machine to a minimum CSP-2 profile followed by application of an appropriate ROCK-TRED primer or base system is the best and recommended installation method for CHEM-WALL SEALER applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
Clean Up
Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.
Disposal
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
Important Notice
Always read and acquaint yourself with ROCK-TRED’s Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty
Brand:Rock TredSKU:RT430-COO-1.5Tags:Clear Epoxy, Rock Tred, Sealers
Product details
Chem-Wall Sealer
Available Sizes
1.5 Gallon Units
Advantages
100% solids
Excellent adhesion
High build formulation
Good chemical and abrasion resistance
Easy mix ratio and application methods
VOC compliant
Good UV resistance
Manufactured in a white color base, but able to be field pigmented in any ROCK-TRED Standard Color
Description
CHEM-WALL SEALER is 100% solids, high viscosity, 2-component, aliphatic epoxy. CHEM-WALL SEALER provides excellent durability, abrasion resistance and protection from a wide range of chemicals.
Uses
CHEM-WALL SEALER is used where a high-build protective polymer coating is desired on walls and ceilings. This coating is suitable for application as a neat finish coat over prepared and primed surfaces, or as a build/body coat between primer and high-performance finish coats such as CHEM-THANE WB. CHEM-WALL SEALER is easy to use, VOC compliant and meets all USDA/FDA guidelines for use in federally inspected facilities.
Typical Coverage
CHEM-WALL SEALER is normally installed at 135-200 square feet per gallon on vertical and overhead substrates.
Physical Properties
Volume mix ratio
2 to 1 (Resin to Hardener)
Viscosity (mixed)
19,000-25,000 CPS Typical
Solids Content (%)
100 % (ASTM D-2697)
Hardness (ASTM D-2240)
70-80 (Shore D)
VOC
Compliant with all US Regulations
Application Temps.
60° – 85° F
Gel Time
40-60 minutes @ 75° F
Dry to Touch (recoat with compatible products)
1-3 hours @ 75° F
Through Cure
6-8 hours @ 75° F
Open for light traffic/use
24 hours @ 75° F
Shelf Life
1 Year in unopened units
Limitations & For Best Results
Do not thin this product.
Do not apply when Humidity exceeds 70% indoors.
Do not allow to puddle during application.
Allow each coat to dry to ‘tack-free’ prior to re-coat
When re-coating, always apply the next coat within 24 hours of completing the previous coat.
CHEM-WALL SEALER is a WHITE COLOR BASE. Field pigmenting with ROCK-TRED standard colors will result in a lighter color than is shown on the ROCK-TRED STANDARD COLOR CHART.
Product Application
Apply using brush, roller and/or airless sprayer. ROCKTRED product test data is based on environmental temperatures of 75° F (24° C). Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.
Color and Textures
CHEM-WALL SEALER is manufactured as a white color base and can be field pigmented using one 1.5 Jar unit of ROCK-TRED UNIVERSAL colorant per 1.5-gal unit. Most ROCK-TRED products are available in a wide range of textures.
Chemical Resistance
Always refer to ROCK-TRED’s chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.
Product Storage
DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.
Surface Preparation
Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a diamond grinding machine to a minimum CSP-2 profile followed by application of an appropriate ROCK-TRED primer or base system is the best and recommended installation method for CHEM-WALL SEALER applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
Clean Up
Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.
Disposal
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
Important Notice
Always read and acquaint yourself with ROCK-TRED’s Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty
Brand:Rock TredSKU:RT430-COO-1.5Tags:Clear Epoxy, Rock Tred, Sealers
Available Sizes
1.5 Gallon Units
Advantages
100% solids
Excellent adhesion
High build formulation
Good chemical and abrasion resistance
Easy mix ratio and application methods
VOC compliant
Good UV resistance
Manufactured in a white color base, but able to be field pigmented in any ROCK-TRED Standard Color
Description
CHEM-WALL SEALER is 100% solids, high viscosity, 2-component, aliphatic epoxy. CHEM-WALL SEALER provides excellent durability, abrasion resistance and protection from a wide range of chemicals.
Uses
CHEM-WALL SEALER is used where a high-build protective polymer coating is desired on walls and ceilings. This coating is suitable for application as a neat finish coat over prepared and primed surfaces, or as a build/body coat between primer and high-performance finish coats such as CHEM-THANE WB. CHEM-WALL SEALER is easy to use, VOC compliant and meets all USDA/FDA guidelines for use in federally inspected facilities.
Typical Coverage
CHEM-WALL SEALER is normally installed at 135-200 square feet per gallon on vertical and overhead substrates.
Physical Properties
Volume mix ratio
2 to 1 (Resin to Hardener)
Viscosity (mixed)
19,000-25,000 CPS Typical
Solids Content (%)
100 % (ASTM D-2697)
Hardness (ASTM D-2240)
70-80 (Shore D)
VOC
Compliant with all US Regulations
Application Temps.
60° – 85° F
Gel Time
40-60 minutes @ 75° F
Dry to Touch (recoat with compatible products)
1-3 hours @ 75° F
Through Cure
6-8 hours @ 75° F
Open for light traffic/use
24 hours @ 75° F
Shelf Life
1 Year in unopened units
Limitations & For Best Results
Do not thin this product.
Do not apply when Humidity exceeds 70% indoors.
Do not allow to puddle during application.
Allow each coat to dry to ‘tack-free’ prior to re-coat
When re-coating, always apply the next coat within 24 hours of completing the previous coat.
CHEM-WALL SEALER is a WHITE COLOR BASE. Field pigmenting with ROCK-TRED standard colors will result in a lighter color than is shown on the ROCK-TRED STANDARD COLOR CHART.
Product Application
Apply using brush, roller and/or airless sprayer. ROCKTRED product test data is based on environmental temperatures of 75° F (24° C). Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.
Color and Textures
CHEM-WALL SEALER is manufactured as a white color base and can be field pigmented using one 1.5 Jar unit of ROCK-TRED UNIVERSAL colorant per 1.5-gal unit. Most ROCK-TRED products are available in a wide range of textures.
Chemical Resistance
Always refer to ROCK-TRED’s chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.
Product Storage
DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.
Surface Preparation
Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a diamond grinding machine to a minimum CSP-2 profile followed by application of an appropriate ROCK-TRED primer or base system is the best and recommended installation method for CHEM-WALL SEALER applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
Clean Up
Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.
Disposal
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
Important Notice
Always read and acquaint yourself with ROCK-TRED’s Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty
Brand:Rock TredSKU:RT430-COO-1.5Tags:Clear Epoxy, Rock Tred, Sealers
Product information
COL-66ca9ed916ba857da6cef040827bbb202fd9fbd2
Other Products / General Merchandise / Other Products
Other Products / General Merchandise / Other Products
